..Alesis M1 Active Mk2 zabluda?..

[lesha]

evo specifikacija:

CROSSOVER SECTION

Crossover type: 4th-order, 24dB/octave Linkwitz-Riley @ 2000Hz
Input Impedance: 20kOhm balanced 10kOhm unbalanced
Low Frequency Filter: 4th order optimal Q high pass filter at 48Hz with +3 dB
equalization

AMPLIFIER SECTION

LOW FREQUENCY AMPLIFIER
Rated power output: 75 watts, 6 Ohm load
Distortion: <0.02% THD @ 30 watts/8 Ohm 20Hz-20kHz
Slew rate: 19V/?sec
Signal-to-Noise ratio: >110dB referenced to 60 watts @ 8 Ohm, “A” weighted, 1kHz

HIGH FREQUENCY AMPLIFIER
Rated Power Output: 25 watts, 4 Ohm load
Distortion: 0.025% THD @ rated power
Slew rate: 9V/?sec
Signal-to-Noise ratio: >112dB @ rated output

ACOUSTIC SECTION

Free-Field Frequency Response: ?2dB, 50Hz to 20KHz
Lower Cutoff Frequency: 40Hz -10dB
Upper Cutoff Frequency: 23.5KHz –10dB
Maximum Peak SPL per pair: = 118dB SPL @ 1m
Maximum short term SPL: 80Hz to 3.0KHz = 105dB SPL @ 1m

[boggy]

Originally Posted by lesha

evo specifikacija:

CROSSOVER SECTION

Crossover type: 4th-order, 24dB/octave Linkwitz-Riley @ 2000Hz
Input Impedance: 20kOhm balanced 10kOhm unbalanced
Low Frequency Filter: 4th order optimal Q high pass filter at 48Hz with +3 dB
equalization

AMPLIFIER SECTION

LOW FREQUENCY AMPLIFIER
Rated power output: 75 watts, 6 Ohm load
Distortion: <0.02% THD @ 30 watts/8 Ohm 20Hz-20kHz
Slew rate: 19V/?sec
Signal-to-Noise ratio: >110dB referenced to 60 watts @ 8 Ohm, ?A? weighted, 1kHz

HIGH FREQUENCY AMPLIFIER
Rated Power Output: 25 watts, 4 Ohm load
Distortion: 0.025% THD @ rated power
Slew rate: 9V/?sec
Signal-to-Noise ratio: >112dB @ rated output

ACOUSTIC SECTION

Free-Field Frequency Response: ?2dB, 50Hz to 20KHz
Lower Cutoff Frequency: 40Hz -10dB
Upper Cutoff Frequency: 23.5KHz ?10dB
Maximum Peak SPL per pair: = 118dB SPL @ 1m
Maximum short term SPL: 80Hz to 3.0KHz = 105dB SPL @ 1m

Nista o osetljivosti ulaza, valjda je +4dBu... kako si razbalansirao konekciju... presao sa nebalansiranog na balansirani ulaz?

Na kraju, ako nista ne uspemo.. ocepi ti njega do kraja i utisavaj na karti...

ili nadji neki master volume, mozda ti ne bi bio los neki di-box sa atenuacijom... ima li tako neceg da se kupi za male pare?

pozdrav

bogi

[lesha]

Originally Posted by boggy

Nista o osetljivosti ulaza, valjda je +4dBu... kako si razbalansirao konekciju... presao sa nebalansiranog na balansirani ulaz?

Na kraju, ako nista ne uspemo.. ocepi ti njega do kraja i utisavaj na karti...

ili nadji neki master volume, mozda ti ne bi bio los neki di-box sa atenuacijom... ima li tako neceg da se kupi za male pare?

ima kombinovani ulaz - TRS balanced/unbalanced / XLR

ja sam koristio nebalansirani TRS..

zanima me koliko bi trebao da utisam gain na softverskom mixeru bez boxa..

[boggy]

Originally Posted by lesha

ima kombinovani ulaz - TRS balanced/unbalanced / XLR

ja sam koristio nebalansirani TRS..

zanima me koliko bi trebao da utisam gain na softverskom mixeru bez boxa..

Pa tako da ti prija slusanje... probaj pa javi... nema nacina da sada procenim koliko decibela treba nesto utisati .... najbolje probaj pa kazi koliko si morao da utisas...

pozdrav
bogi

[kejkz]

Ja licno gotovo nikada ne smanjujem nivo preko miksera kartice kada radim svoju muziku ili miks, jer za to ne vidim potrebu, cilj mi je da iz same kartice izlazi ceo dinamicki opseg muzike koju radim. Koristim kombinaciju rme hdsp9632 i alesis, i jacinu sam na samom Alesisu podesio na vrednost oko 6. Preporucujem ti, ako vec zelis da koristis alesise na visoj jacini, da koristis analogni atenuator, i to A-design ATTY:http://www.adesignsaudio.com/atty.htm. Za te pare (oko 120 e ili i manje) nema boljeg resenja, a imas sve sto ti treba za transparentno slusanje, a da zvuk kartice preko miksera podesis na maksimum. Na nesrecu, ne znam gde se moze kupiti kod nas, ja sam ATTY kupio preko interneta.
A to sto mp3 i zvuci iz Swinjdowsa zvuci distorzirano, mislim da je vise problem samih fajlova nego tvog audio sistema.